Last Updated on October 20, 2024 by Maged kamel
Introduction to Tension members.
Introduction to tension members- tension yielding.
We will begin a new subject, Introduction to Tension Members.
The first section discusses where to employ the tension members.
The second item is the AISC chapter, which regulates tension member design.
The third item explains net and gross areas. The gross area is the section area without considering any deductions for fasteners.
The net area is the section’s area minus the fastener’s area. Later, we’ll look into fasteners like bolts for allowances.
There are net and special tables for determining the final value of the effective net area.
The fourth component discusses tensile yielding &tensile rupture and gauge line information.
The fifth component provides the design parameters for tension members in the LRFD and ASD, the reduction factors ฯt and ฮฉt.
The sixth item is the tables for various shapes, the relevant yield, and F ultimate stresses for tension members.
Tension members are used for bridges, roof trusses, towers, and bracings. Tension members are considered when used as tie rods.
Selecting a section to be used as a tension member is one of the simplest problems encountered in design, compared with columns and beams, so the design of tension members is considered simple.
The related division in the specification for Tension members.
The next slide includes the chapter used for the design of tension members and then shows the section in the chapter for tension members. Chapter D is used. D-2 governs the Tensile strength. AISC-360-16 page 16-1-28.
There are two items: Tensile Yielding and Tensile rupture. For tensile yielding, the P nominal is estimated as equal to the product of Fy*Ag, where Fy is the yield stress, and Ag is the gross area.
For the design strength, multiply by ฯt =0.90. While for the allowable strength, multiply by (1/ ฮฉt) where ฮฉt=1.67.
Item b) is for tensile rupture at the places of bolts or welds. The nominal load Pn = Fu*Ae, where Ae is the effective area.
However, the LRFD parameter differs: for tensile rupture ฯt =0.75, less than the value given for tensile yielding, which is 0.90.
For the ASD design, based on the relation of ฯ*ฮฉ=1.5, then ฮฉt=2.00. Fy is yield strength, and Fult is the ultimate strength. D-3 includes the effective net area and is to be estimated from B 4-3, Aeff=Anet*U factor, U, shear lag factor=1.
In the next slide, we can see two cases. The first case is when the two members are connected fully, like a bolted plate and spliced channel. The effective area equals the net area, and the u factor, the shear lag factor, equals one.
Whenever two channels are connected only at the upper and lower flange, while the web areas are not connected, the effective area will be considered smaller than the net area, and the U value will be less than one.
This is the provision from the AISC code for the net area for tension members and the different terms used.
The shear lag factor U value is obtained from Table D3-1.
Tension yielding.
The tension yield picture was quoted from the external linkโa BEGINNER’S GUIDE TO THE STEEL CONSTRUCTION MANUAL, 14THย ED.
As an introduction to tension members, we would want to examine the various failure modes.
There are many good illustrations, such as a section for the W section; if we deal with tension yielding, there is a failure mode on the positions distant from the bolts. When tension forces are applied from the ends, the failure will occur at a position other than the bolts’ path.
This failure mechanism focuses on yielding in the gross cross-sectional area.
T=Ag*Fy calculates the tension force at failure. An is the original shape, and b is after the section’s tension yielding.
Tensile Rupture types.
This is the first failureโa vertical line passed by the line of the bolts in a direction perpendicular to the force direction.
The second failure is shown here as a zigzag line, from which the net area was estimated. We must consider the spacing S and the perpendicular distance g between bolts.
The damage occurs due to the Punching of a hole.
Looking back to Prof McCormack’s notes, he stated the long-standing practice of punching holes with a 1/16 inch diameter larger than the bolts.
When this technique was followed, punching a hole was expected to harm or destroy an additional 1/16 inch of the surrounding metal. In actuality, add 1/16+1/16 inch to the diameter of the bolt.
Results
Last Updated on October 20, 2024 by Maged kamel
Last Updated on October 20, 2024 by Maged kamel
#1. What is the Hole diameter for 7/8 inch bolt?
The following post contains an Easy introduction to Tension members-part-2.
For a useful external Chapter 3 – Tension Members–ย Bartlett Quimby